TNU3N602T33,Huawei OptiX OSN 9800 High Performance Programable Line Service Processing Board

Huawei OptiX OSN 9800 High Performance Programable Line Service Processing Board TNU3N602T33 Overview

TNU3N602: 2*200G/400G high performance Programable Line Service Processing Board.

TNU3N602T32: 2*200G/400G high performance Programable Line Service Processing Board;

TNU3N602T33: 2*200G/400G Programable Line Service Processing Board

As an OTN line board, a TNU3N602T32/TNU3N602T33 board converts ODU0, ODU1, ODU2/ODU2e, ODU3, ODU4, and ODUflex signals carried over ITU-T G.694.1 compliant DWDM wavelengths.

The TNU3N602T32/TNU3N602T33 board consists of a WDM-side rate/modulation format tunable optical module, a signal processing module, a control and communication module, and a power module. The overall board function is the sum of functions provided by the two ports, and the function of each port varies depending on the port mode. Therefore, the following describes working principles and signal flows by port mode.

This topic describes the N602 board parameters that can be set or queried using the NMS.

Functions and Features of the TNU3N602T33 Board

Function and Feature	Description
Basic function	Provides two line ports and supports conversion between a maximum of 640 x ODU0/320 x ODU1/80 x ODU2/80 x ODU2e/16 x ODU3/8 x ODU4/640 x ODUflex signals and two channels of OTU4/OTUC2 signals.
Backplane capacity	The maximum capacity is 800 Gbit/s.
WDM specification	Supports the DWDM specifications.
Tunable wavelength	Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
FEC coding	SDFEC2
Line modulation format	200G QPSK wDCM 200G QPSK 400G 16QAM
Typical channel spacing	200G QPSK wDCM: 100GHz+n6.25GHz(n=0,1,2...) 200G QPSK, 400G 16QAM: 75GHz+n6.25GHz(n=0,1,2...)
OTN overhead protocol	Supports the OTN frame format and overhead processing defined by ITU-T G.709.
OTN overhead	WDM-side OTUC4/OTUC2 layer: supports SM overhead processing. ODUC4/ODUC2layer: supports PM and TCM overhead processing. ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing and non-intrusive monitoring of PM and TCM overheads.
Intra-board 1+1 protection	Supported NOTE: Supports intra-board 1+1 protection when working with the optical protection boards
ODUk SNCP	Supported
Tributary SNCP	Supported
Electrical-layer ASON	Supported
Optical-layer ASON	Supported
Digital optical label	When LS Ability is enabled, the board supports loading low-frequency pilot-tone modulation signals and overheads during wavelength conversion, and can work the optical-layer board that supports the digital optical label function to detect optical power and overheads and report optical performance data.
Physical clock	Supported NOTE: When the ODU cross-connect granularity of an OTN line port is set to the maximum granularity supported by the port, physical clock synchronization is not supported. The physical clock can be used only after lower-order ODU cross-connections are configured.
IEEE 1588v2	Not supported
Outband DCN	Supports communication over ESCs.
Test frame	Not supported
PRBS	Supports the PRBS function on the WDM side.
Latency measurement	The board supports latency measurement in the WDM-side optical port direction (upstream direction).When higher-order ODU4 cross-connections are created on the board, TCM section latency measurement is supported for higher-order ODU4 channels. When lower-order ODUk cross-connections are created on the board, PM/TCM section latency measurement is supported for higher-order ODU4 channels, and TCM section latency measurement is supported for lower-order ODUk channels. The board supports PM and TCM latency measurement at the ODUCn layer.
Channel loopback	ODUk (k=0, 1, 2, 3, 4, flex) channel loopbacks
Port loopback	Supports WDM Side Loopback
Alarm and performance event monitoring	Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line failures. Monitors parameters such as the bias current, temperature, and optical power of the laser. Monitors OTN alarms and performance events.

Hunan Moka Information Technology Co., Ltd.

A professional import and export trade company specializing in the agency sales and services of the full range of Cisco products in the United States. Our product range includes Cisco switches, Cisco routers, Cisco firewalls, Cisco wireless APs, Cisco conference terminals, Cisco optical modules, Cisco fiber optic jumpers, Cisco industrial switches, and Cisco software licenses. As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects. As a result, you can obtain the best discounts from Cisco China, typically ranging from 60% to over 90%. Due to Cisco's global sales policy, if you order Cisco licenses, with your consent and permission, we will assist you in installing and activating Cisco licenses within China. Alternatively, you can activate them in your own country, and we will transfer the licenses to you. All you need is a Cisco Smart Account. When the Cisco licenses expire, you can choose to renew them yourself or contact us.

As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects.

Huawei OptiX OSN 9800 High Performance Programable Line Service Processing Board TNU3N602T33

DETAILS

YOU MAY ALSO LIKE

Get a free consultation

Innovatively safeguards your investments for the future