TNS4N402-Huawei OptiXtrans E9600 2 Port 100Gbit/s Programable Hybrid Line Service Processing Board

Backplane capacity

The total backplane bandwidth is 200 Gbit/s.

WDM specification

Supports ITU-T G.694.1-compliant DWDM specifications.

Tunable wavelength

Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).

FEC coding

SDFEC2

Line modulation format

• 100G QPSK
• 100G QPSK wDCM

Typical channel spacing

50GHz*n(n=1,2...)(Only the standard center frequency of 50 GHz is supported.)

OTN overhead protocol

Supports the OTN frame format and overhead processing defined by ITU-T G.709.

OTN overhead

• WDM-side OTU4 layer: supports SM overhead processing.
• ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing.
• ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports non-intrusive monitoring of PM and TCM overheads.

Intra-board 1+1 protection

Supported

NOTE:

Supports intra-board 1+1 protection when working with optical protection boards.

ODUk SNCP

Supported

Tributary SNCP

Supported

Electrical-layer ASON

Supported

Optical-layer ASON

Supported

NOTE:

Only ASON without optical parameters is supported in high SOP mode.

Digital optical label

When LS Ability is enabled, the board supports loading low-frequency pilot-tone modulation signals and overheads during wavelength conversion, and can work the optical-layer board that supports the digital optical label function to detect optical power and overheads and report optical performance data.

Physical clock

Supported

NOTE:

When the ODU cross-connect granularity of an OTN line port is set to the maximum granularity supported by the port, physical clock synchronization is not supported. The physical clock can be used only after lower-order ODU cross-connections are configured.

IEEE 1588v2

Not supported

ITU-T G.8275.1

Not supported

ITU-T G.8273.2

Not supported

Outband DCN

Supports communication over ESCs.

Test frame

Not supported

PRBS

Supports the PRBS function on the WDM side.

Latency measurement

The board supports latency measurement in the WDM-side optical port direction (upstream direction). When higher-order ODU4 cross-connections are created on the line board, TCM section latency measurement is supported for higher-order ODU4 channels. When lower-order ODUk cross-connections are created on the line board, PM/TCM section latency measurement is supported for higher-order ODU4 channels, and TCM section latency measurement is supported for lower-order ODUk channels.

Channel loopback

ODUk (k=0, 1, 2, 2e, 3, flex) channel loopbacks

Port loopback

Supports WDM Side Loopback

Alarm and performance event monitoring

• Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line failures.
• Monitors parameters such as the bias current, temperature, and optical power of the laser.
• Monitors OTN alarms and performance events.

Basic function

A maximum of 80 Gbit/s SDH services are supported

• 8 x STM-64<->8 x ODU2<->1 x ODU4<->1 x OTU4
• 32 x STM-16<->32 x ODU1<->1 x ODU4<->1 x OTU4

Backplane capacity

The total backplane bandwidth is 80 Gbit/s.

Service processing

VC-12, VC-3, VC-4, VC-4-4c, VC-4-16c, VC-4-64c

Overhead processing

• Processes the section overheads of STM-16/STM-64 signals.
• Supports the transparent transmission and termination of path overheads.
• Supports the setting and query of the J0, J1, and C2 bytes.
• Supports ECC communication.
• Supports transparent transmission of DCC channels.

SDH SNCP

Supported

Linear MSP

Supported

Ring MSP

Supports two-fiber bidirectional ring MSP

Physical clock

Supports SDH clock synchronization.

Outband DCN

Supported

Channel loopback

Supports VC loopbacks.

Port loopback

Supports Virtual Port loopbacks.

2M ASON

Supported

NOTE:

Only supported when the E9624 is used.

Alarm and performance event monitoring

• Supports the monitoring of B1 bytes to help locate line faults.
• Supports the monitoring of B2 bytes to help locate line faults.