TNG1N401,Huawei OptiXtrans E9600 1 Port 100G Line Service Processing Board

Huawei OptiXtrans E9600 1 Port 100G Line Service Processing Board TNG1N401 Overview

TNG1N401 Is Huawei OptiXtrans E9600 1 Port 100G Line Service Processing Board

As an OTN line board, the N401 board converts 80 ODU0, 40 ODU1, 10 ODU2, 10 ODU2e, 2 ODU3, 1 ODU4, or 80 ODUflex signals into one OTU4 signal carried over an ITU-T G.694.1 compliant DWDM wavelength, and vice versa. Each port on the board supports a mix of ODU0, ODU1, ODU2/ODU2e, ODU3, and ODUflex signals. The N401 board uses coherent detection technology and is targeted for coherent communications.

TNG1N401: 1 x 100 Gbit/s Line Service Processing Board

The N401 board consists of a WDM-side optical module, signal processing module, control and communication module, and power supply module.

The total backplane bandwidth is 100 Gbit/s.

The board TNG1N401 Have Four indicators are present on the front panel:

Board hardware status indicator (STAT) - triple-colored (red, green, yellow)

Service active status indicator (ACT) - dual-colored (red, green)

Board software status indicator (PROG) - dual-colored (red, green)

Service alarm indicator (SRV) - triple-colored (red, green, yellow)

Huawei OptiXtrans E9600 Series Optical Transmission Platform's board category as below:

OTN Tributary Board
OTN Line Board
Universal Line Board
General Service Processing Board
Packet Service Processing Board
EoO Board
SDH Board
EoS Board
Turbo WDM Board
Submarine Board
Clock Board
Cross-Connect Board
System Control and Communication Board

Functions and Features of the TNG1N401 Board (OTN Tributary)

Function and Feature	Description
Backplane capacity	The total backplane bandwidth is 100 Gbit/s.
WDM specification	Supports the DWDM specifications.
Tunable wavelength	Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
FEC coding	T51/T61/T5U/T62/T65/T69HP/T65HP/T50/T51HP/T52/T53/T63/T52HP/T53HP/T63HP/T61HP/F51/A51/A62: SDFEC2 Gray-light modules: FEC
Line modulation format	NRZ 100G QPSK 100G QPSK wDCM
OTN overhead protocol	Supports the OTN frame format and overhead processing defined by ITU-T G.709.
OTN overhead	WDM-side OTU4 layer: supports SM overhead processing. ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing. ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports non-intrusive monitoring of PM and TCM overheads.
Intra-board 1+1 protection	Supported NOTE: Supports intra-board 1+1 protection when working with optical protection boards.
ODUk SNCP	Supported
Tributary SNCP	Supported
Electrical-layer ASON	Supported
Optical-layer ASON	Supported NOTE: In versions earlier than V100R007C00SPC500, ASON is not supported in high SOP mode. In V100R007C00SPC500 and later versions, only ASON without optical parameters is supported in high SOP mode.
Physical clock	Supported NOTE: When the ODU cross-connect granularity of an OTN line port is set to the maximum granularity supported by the port, physical clock synchronization is not supported. The physical clock can be used only after lower-order ODU cross-connections are configured.
IEEE 1588v2	Not supported
Outband DCN	Supports communication over ESCs.
Test frame	Not supported
PRBS	Supports the PRBS function on the WDM side.
Latency measurement	The board supports latency measurement in the WDM-side optical port direction (upstream direction). When higher-order ODUk cross-connections are created on the line board, TCM section latency measurement is supported for higher-order ODUk channels. When lower-order ODUk cross-connections are created on the line board, PM/TCM section latency measurement is supported for higher-order ODUk channels, and TCM section latency measurement is supported for lower-order ODUk channels.
Channel loopback	ODUk (k=0, 1, 2, 3, flex) channel loopbacks
Port loopback	Supports WDM Side Loopback
Alarm and performance event monitoring	Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line faults. Supports the monitoring of the laser bias current. Supports the laser temperature monitoring. Supports the optical power monitoring. Supports the monitoring of OTN alarms and performance events.

Functions and Features of the TNG1N401 Board (Regeneration)

Function and Feature	Description
Basic function	Electrically regenerates optical signals at an electrical REG station. NOTE: When the CFP,4*25Gb/s(1310nm Band),103.125Gb/s &111.81Gb/s-100G Dual Rates,-1.3dBm,4.5dBm,-8.6dBm,Straight LC,SMF,OMA,10km modules are used, the TNG1N401 board does not support relay mode.
Regeneration mode	Unidirectional regeneration
Regeneration rate	OTU4
WDM specification	Supports the DWDM specifications.
Tunable wavelength	Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
FEC coding	SDFEC2
Line modulation format	100G QPSK 100G QPSK wDCM
OTN overhead	WDM-side OTU4 layer: supports SM overhead processing. ODU4 layer: supports PM and TCM overhead processing. ODU4 layer: supports non-intrusive monitoring of PM and TCM overheads.
Optical-layer ASON	Supported NOTE: In versions earlier than V100R007C00SPC500, ASON is not supported in high SOP mode. In V100R007C00SPC500 and later versions, only ASON without optical parameters is supported in high SOP mode. For the WDM-side A51 or A62 optical module, the receive and transmit wavelengths must be the same. Both A51 and A62 modules do not support wavelength change for unidirectional regeneration.
Outband DCN	Supports ESC communication.
Alarm and performance event monitoring	Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line faults. Supports the monitoring of the laser bias current. Supports the laser temperature monitoring. Supports the optical power monitoring. Supports the monitoring of OTN alarms and performance events.

Hunan Moka Information Technology Co., Ltd.

A professional import and export trade company specializing in the agency sales and services of the full range of Huawei telecom equipment,Huawei parts,Cisco products in the United States. Our product range includes Cisco switches, Cisco routers, Cisco firewalls, Cisco wireless APs, Cisco conference terminals, Cisco optical modules, Cisco fiber optic jumpers, Cisco industrial switches, and Cisco software licenses. As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects. As a result, you can obtain the best discounts from Cisco China, typically ranging from 60% to over 90%. Due to Cisco's global sales policy, if you order Cisco licenses, with your consent and permission, we will assist you in installing and activating Cisco licenses within China. Alternatively, you can activate them in your own country, and we will transfer the licenses to you. All you need is a Cisco Smart Account. When the Cisco licenses expire, you can choose to renew them yourself or contact us.

As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects.

TNG1N401-Huawei OptiXtrans E9600 1 Port 100G Line Service Processing Board

DETAILS

YOU MAY ALSO LIKE

Get a free consultation

Innovatively safeguards your investments for the future