TNF1LQM,03020LYK,Huawei OSN 1800 Optical Transponder LQM Board

Huawei OSN 1800 Optical Transponder LQM Board TNF1LQM 03020LYK Overview

TNF1LQM: 4 x Multi-rate Ports Wavelength Conversion Board

The available hardware versions for the LQM are TNF1 and TNF2.

The LQM can be used in two different application scenarios: convergence of Any service signals and regeneration of OTU1 optical signals.

The LQM board consists of the client-side optical module or client-side electrical module, the WDM-side optical module, the service en/de-capsulation and processing module, the clock module, the variable optical attenuator, the communication module, and the power supply module. The variable optical attenuator is optional. If you need this module, contact Huawei.

In the signal flow of the LQM board, the transmit and the receive directions are defined. The transmit direction is defined as the direction from the client side of the LQM to the WDM side of the LQM, and the receive direction is defined as the reverse direction.

Transmit direction

The client-side optical module receives optical signals from client equipment through the RX1-RX4 ports, and performs O/E conversion.

The client-side electrical module receives electrical signals from client equipment through the RX1-RX4 ports, and performs level conversion.

After conversion, the four channels of electrical signals are sent to the service en/de-capsulation and processing module. The module performs processes such as multiplexing, clock generating and frame processing. Then, the module outputs a channel of OTU1 signals.

The OTU1 signals are sent to the WDM-side optical module. After performing E/O conversion, the module sends out the G.694.1-compliant 2.67 Gbit/s optical signals at DWDM standard wavelengths or the G.694.2-compliant 2.67 Gbit/s optical signals at CWDM standard wavelengths. The optical signals are output through the OUT1 and OUT2 optical ports.

Receive direction

The WDM-side optical module receives the G.694.1-compliant 2.67 Gbit/s optical signals at DWDM standard wavelengths or the G.694.2-compliant 2.67 Gbit/s optical signals at CWDM standard wavelengths from the WDM side through the IN1 and IN2 optical ports. Then, the module performs O/E conversion.

After O/E conversion, the signals are sent to the service en/de-capsulation and processing module. The module performs processes such as decapsulation, clock recovery and demultiplexing. Then, the module outputs four channels of electrical signals at any rate.

The client-side optical module performs E/O conversion of the optical signals, and the client-side electrical module performs level conversion of the electrical signals, and then outputs four channels of client-side signals through the TX1-TX4 ports.

Functions and Features of the TNF1LQM Board

Basic function	TNF1LQM: 4 x Any (125 Mbit/s - 1.25 Gbit/s) <-> 1 x OTU1 Implements bidirectional regeneration of one OTU1 service. WDM-side optical ports provide the dual feeding and selective receiving function. TNF2LQM: 4 x Any (125 Mbit/s - 2.5 Gbit/s) <-> 1 x OTU1 Implements bidirectional regeneration of two OTU1 services. WDM-side optical ports provide the dual feeding and selective receiving function. NOTE: The RX1/TX1 port supports the signals at a rate of 125 Mbit/s to 2.5 Gbit/s.
Service type	Convergence services: STM-1: SDH services at a rate of 155.52 Mbit/s. STM-4: SDH services at a rate of 622.08 Mbit/s. STM-16: SDH services at a rate of 2.488 Gbit/s. OC-3: SONET services at a rate of 155.52 Mbit/s. OC-12: SONET services at a rate of 622.08 Mbit/s. OC-48: SONET services at a rate of 2.488 Gbit/s. OTU1: OTN services at a rate of 2.67 Gbit/s. FE: Fast Ethernet services at a rate of 125 Mbit/s. Supports FE optical signals and FE electrical signals. GE: Gigabit Ethernet services at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals. ESCON: Enterprise system connection services at a rate of 200 Mbit/s. FC100: Fiber channel services at a rate of 1.06 Gbit/s. FC200: Fiber channel services at a rate of 2.12 Gbit/s. FICON: Fiber channel services at a rate of 1.06 Gbit/s. FICON EXPRESS: Fiber channel services at a rate of 2.12 Gbit/s. DVB-ASI (Digital Video Broadcasting - Asynchronous Serial Interface): Digital TV services at a rate of 270 Mbit/s. SDI (Digital Video Broadcasting - Serial Digital Interface): Digital TV services at a rate of 270 Mbit/s. HD-SDI: High-definition digital TV services at a rate of 1.485 Gbit/s or 1.4835 Gbit/s. CPRI option2: The rate is 1.2288 Gbit/s. (Only F2LQM supports.) CPRI option3: The rate is 2.4576 Gbit/s. (Only F2LQM supports.) Regeneration services: OTU1: OTN services at a rate of 2.67 Gbit/s. (Only the TX1/RX1 port on the TNF1LQM board supports; Only the TX1/RX1 and TX2/RX2 ports on the TNF2LQM board support.) NOTE: FC100, FC200, FICON, and FICON EXPRESS services that the TNF1LQM receives can be configured as sliced services. The "SDI" is also called the "SD-SDI" according to SMPTE 259M standard. It is recommended that F2LQM boards transmit and receive CPRI option2 services in ODU0 non-convergence mode, and CPRI option3 services in ODU1 non-convergence mode.
FEC mode	Supports forward error correction (FEC) that complies with ITU-T G.709.
Ethernet service mapping mode	TNF1LQM: Supports encapsulation of GE services in GFP-F (ITU-T G.7041) (displayed as GE on the NMS) and GFP-T (ITU-T G.7041) modes. Supports encapsulation of FE services in GFP-F (ITU-T G.7041) mode (displayed as FE on the NMS). TNF2LQM: Supports encapsulation of GE services in GFP-T (ITU-T G.7041) and TTT-GMP (ITU-T G.709) modes (displayed as GE(TTT-GMP) on the NMS). Supports encapsulation of FE services in GFP-F SLICE+BMP mode. NOTE: You are advised to use FE electrical modules to transmit FE electrical services. If you use GE electrical modules to transmit FE electrical services, note the following points: The system control board type must be TNF1SCC. The GE electrical module must be used on the client side of the local and remote ends to add and drop FE electrical services. The service type must be configured as GE and the encryption mode as GFP-T. When the GE electrical module is transmitting FE services, the RMON statistics cannot be collected.
Alarms and performance events monitoring	Monitors B1, SM_BIP8, PM_BIP8 bytes to help locate faults. Monitors performance parameters and alarm signals, including the monitoring of laser bias current, laser working temperature and optical power on the WDM side. LQM monitors the RMON performance of GE/FE services.
OTN function	Supports mapping of client-side services into OTU1 services. Supports the OTN frame format and overhead processing recommended in ITU-T G.709. TNF1LQM supports the PM function for ODU1 and the SM function for OTU1. TNF2LQM supports the PM function for ODU0 and ODU1 and the SM function for OTU1. NOTE: When the LQM board is used as a regeneration board, it does not support the PM overhead configuration.
Variable optical attenuator	The TNF2LQM board can adjust the optical power of the WDM-side signals using the SFP EVOA module housed at the VO/VI port. The allowable attenuation range is from 0 dB to 20 dB.
Intelligent fiber (IF) function	The TNF1LQM board can automatically insert maintenance code streams to the client-side optical ports on the downstream board in the case of an input fault on the client or WDM side of the upstream board. Then the fault information can be transmitted to the client side of the downstream board. TNF2LQM: Not supported
Regeneration board	The WDM-side signals of the LQM board can be regenerated by the LWX2, LQM, or TNF1LQM2 board.
Synchronous Ethernet services	The TNF2LQM board supports the transparent transmission of synchronous Ethernet clock signals that are compliant with G.8261.
Protection schemes	TNF1LQM: Supports intra-board 1+1 protection Supports client 1+1 protection TNF2LQM: Supports intra-board 1+1 protection Supports client 1+1 protection Supports ODUk SNCP (k = 0, 1) protection
Loopback	Supports WDM-side inloop. Supports WDM-side outloop. Supports client-side inloop. Supports client-side outloop.
ALS function	Supports the ALS function on the client side. NOTE: When the client side receives OTU1 services, the ALS function is disabled. That is, the laser stays in enabling state.
ESC function	Supported
Cross-connect function	Not supported
LPT function	The board supports the LPT function only when the client-side service type is GE or FE. The board supports port-based LPT.
PRBS test	The PRBS function on the client side is supported only when the client-side service type is GE(GFP-T)/STM-1/STM-4/STM-16/OTU1. NOTE: Only TNF2LQM boards that receive/transmit GE (GFP-T) services support PRBS tests.
Port working mode	Supports GE auto-negotiation when GE services encapsulated using GFP-F are received. NOTE: This function is supported only by the TNF1LQM.
Modules at ports	Client-side ports: SFP optical/electrical module Single-fiber bidirectional SFP optical module VO1/VI1-VO2/VI2: EVOA SFP module (Only TNF2LQM supports) WDM-side ports: SFP optical module Single-fiber bidirectional SFP optical module (Only TNF2LQM supports) NOTE: The SFP optical module, SFP electrical module, and single-fiber bidirectional SFP optical module supported by client-side ports can be used together. WDM-side ports support colorless optical modules.
WDM specifications	Supports ITU-T G.694.1-compliant DWDM specifications and ITU-T G.694.2-compliant CWDM specifications.

Hunan Moka Information Technology Co., Ltd.

A professional import and export trade company specializing in the agency sales and services of the full range of Huawei telecom equipment,Huawei parts,Cisco products. Our product range includes Huawei Microwave,Huawe DWDM,Huawei SDH,Huawei OSN Series,Huawei parts, Cisco switches, Cisco routers, Cisco firewalls, Cisco wireless APs, Cisco conference terminals, Cisco optical modules, Cisco fiber optic jumpers, Cisco industrial switches, and Cisco software licenses. As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects. As a result, you can obtain the best discounts from Cisco China, typically ranging from 60% to over 90%. Due to Cisco's global sales policy, if you order Cisco licenses, with your consent and permission, we will assist you in installing and activating Cisco licenses within China. Alternatively, you can activate them in your own country, and we will transfer the licenses to you. All you need is a Cisco Smart Account. When the Cisco licenses expire, you can choose to renew them yourself or contact us.

As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects.

Huawei OSN 1800 Optical Transponder LQM Board TNF1LQM 03020LYK

DETAILS

YOU MAY ALSO LIKE

Get a free consultation

Innovatively safeguards your investments for the future