Huawei OptiXtrans E6600 2 Port 100G Multi-rate Ports Wavelength Conversion Board TMK1LDCA

Basic function

Provides twelve tributary port and one line port to convert received client-side services into OTU signals.

Client-side service type

• 10GE LAN: Ethernet service at a rate of 10.31 Gbit/s.
• 10GE WAN: Ethernet service at a rate of 9.95 Gbit/s.
• STM-64/OC-192: SDH/SONET service at a rate of 9.95 Gbit/s.
• OTU2: OTN service at a rate of 10.71 Gbit/s.
• OTU2e: OTN service at a rate of 11.1 Gbit/s.
• FC800: SAN service at a rate of 8.5 Gbit/s.
• FC1200: SAN service at a rate of 10.51 Gbit/s.
• FC1600: SAN service at a rate of 14.025 Gbit/s.
• FC3200: SAN service at a rate of 28.05 Gbit/s.
• FICON 8G: SAN service at a rate of 8.5 Gbit/s.
• FICON 10G: SAN service at a rate of 10.51 Gbit/s.
• Infiniband 2.5G: SAN service at a rate of 2.5 Gbit/s.
• Infiniband 5G: SAN service at a rate of 5 Gbit/s.
• Infiniband 10G: SAN service at a rate of 10 Gbit/s.
• 40GE (MPO fiber): The rate is 40 Gbit/s.
• OTU4: OTN service at a rate of 111.81 Gbit/s.
• 100GE: Ethernet service at a rate of 103.125 Gbit/s.

NOTE:

When 100GE or OTU4 services are received from port TX11, no service can be received from ports TX1 to TX8.When FC1600 services are received from port TX11, no 100GE or OTU4 service can be received from port TX12.In 100G mode, TX12 cannot be used.The STM-64/OC-192/10G WAN services support synchronous and asynchronous mapping modes.Only in MPO mode, one 40GE service can be received from ports TX5 to TX8 using an MPO fiber.In common mode, ports TX1 to TX10 support 10G Any services. In MPO mode, only ports TX1 to TX4 and ports TX9 and TX10 support 10G Any services.Only ports TX1 to TX4 and ports TX11 and TX12 support FC1600 services.Only ports TX11 and TX12 support 100GE, OTU4, and FC3200 services.

Service mapping mode

• 10GE LAN/100GE service: Supports bit transparent mapping and MAC transparent mapping.
• STM-64/OC-192/10GE WAN service: Supports asynchronous mapping procedure (AMP) and bit-synchronous mapping procedure (BMP) encapsulation modes.

NOTE:

During interconnection with third-party equipment, the STM-64 service uses the asynchronous mapping encapsulation mode.

WDM specification

Supports the DWDM specifications.

Tunable wavelength

Supports the optical tunable transponder. Equipped with this module, the board can tune the optical signal output on the WDM side within the range of 96 wavelengths in extended C-band with the channel spacing of 50 GHz.

FEC coding

Client side:

• Supports FEC and AFEC coding when the client-side service type is OTU2/OTU2e.
• Supports FEC coding when the client-side service type is OTU4.
• Supports RS_FEC coding when the client-side service type is 100GE/FC3200.

WDM side:

• 200G mode: Supports SDFEC and SDFEC2 coding.
• 100G mode: Supports SDFEC2 coding.

NOTE:

For FC services, only FC3200 services support RSFEC, and other FC services do not support FEC.

Line modulation format

• In 200G mode: Supports 200G 16QAM, 200G 16QAM-H, and 200G e16QAM.
• In 100G mode: Supports 100G QPSK wDCM and 100G QPSK.

NOTE:

Only the QPSK wDCM modulation format can be used on a non-coherent hybrid transmission network.

OTN overhead

• At the ODUflex layer: Supports PM overhead processing.
• At the ODU2/ODU2e/ODU3 layer: Supports PM overhead processing.
• At the ODU4 layer:
  • Supports PM overhead processing when 100GE services are received on the client side.
  • Supports PM and TCM overhead processing when OTU4 services are received on the client side. This board supports non-intrusive monitoring of PM and TCM overheads.
• At the ODUC2 layer: Supports PM overhead processing.
• At the OTU4 layer: Supports SM overhead processing on the client sides.
• At the OTUC2/OTU4 layer: Supports SM overhead processing on the WDM side.

LPT

Supports the LPT function when the client-side service is 10GE LAN.

Intra-board 1+1 protection

Supported

NOTE:

Supports intra-board 1+1 protection when working with the OLP board.

Client 1+1 protection

Supported

NOTE:

• When FC services are received on the client side, inter-NE client 1+1 protection (the working and protection channels are not on the same NE) is not supported.
• Common Mode:
  • Supported on ports TX1/RX1 to TX10/RX10 when the board works with SCS/OLP boards.
  • Supported on ports TX11/RX11 and TX12/RX12 when the ports house LC optical modules and the board works with OLP boards.
  • Not supported on ports TX11/RX11 and TX12/RX12 when the ports house MPO optical modules.
• MPO Mode:
  • Supported on ports TX1/RX1 to TX4/RX4 and TX9/RX9 to TX10/RX10 when the board works with SCS/OLP boards.
  • Not supported on ports TX5/RX5 to TX8/RX8.
  • Supported on ports TX11/RX11 and TX12/RX12 when the ports house LC optical modules and the board works with OLP boards.
  • Not supported on ports TX11/RX11 and TX12/RX12 when the ports house MPO optical modules.

ODUk SNCP

Not supported

Optical-layer ASON

Supported

NOTE:

Only supported when the TNZ6UXCMS/TNZ5UXCMS/TNZ8XCH/TNZ3UXCL/TNZ2UXCL board is used.

L1 service encryption

Supports service OPUk payload encryption and decryption.

NOTE:

The service encryption function of the board is determined by the board license.

Digital optical label

When LS Ability is enabled, the board supports loading low-frequency pilot-tone modulation signals and overheads during wavelength conversion, and can work the optical-layer board that supports the digital optical label function to detect optical power and overheads and report optical performance data.

Overtemperature protection

Supported. If the temperature of a board exceeds the upper threshold and services are affected, the board will automatically reset the key chips to prevent a board damage.

ALS

Supported when non-OTN services are received on the client side.

LLDP

Not supported

Physical clock

• When receiving 10GE LAN/100GE services on the client side:
• Synchronous Ethernet transparent transmission is supported and synchronous Ethernet processing is not supported when the port service mapping path is bit transparent mapping(11.1G) or bit transparent mapping ODU4(100G).
• Synchronous Ethernet processing is supported when the port service mapping path is MAC transparent mapping(10.7G) or MAC transparent mapping ODU4(100G).
• When receiving OTU2/OTU4 services on the client side: Physical-layer clocks are supported.
• When receiving OTU2e services on the client side: Physical-layer clocks are not supported.
• On the WDM side: Physical-layer clocks are supported.

IEEE 1588v2

Supported when 10GE LAN MAC transparent mapping(10.7G), or 100GE MAC transparent mapping ODU4(100G) services are received on the client side.

ITU-T G.8275.1

Supported when 10GE LAN MAC transparent mapping(10.7G), or 100GE MAC transparent mapping ODU4(100G) services are received on the client side.

NOTE:

The destination MAC address cannot be set to the non-forwardable address (01-80-C2-00-00-0E). Otherwise, the PTP clock cannot be traced, and the downstream PTP clock may be affected, resulting in PTP clock tracing abnormalities.

ITU-T G.8273.2

Supported

Outband DCN

Supports ESC communication.

NOTE:

When OTUk services are received on the client side, ESC processing is supported.

For details about the DCN types supported by the board, see "Feature Description - Outband DCN - Introduction to DCN - DCN Communication Channel - Comparison Between OSC and ESC".

Test frame

Supported when the client-side service type is 10GE LAN or 100GE and the port service mapping path is MAC transparent mapping.

NOTE:

When the client-side service type is 100GE and the port service mapping path is Bit transparent mapping ODU4(100G) , only downstream test frames are supported.

PRBS

• Supports the PRBS function on the client side when the client-side service type is STM-64/OC-192/OTU2/OTU2e/10GE WAN/OTU4.
• Supports the PRBS function on the WDM side.

Latency measurement

• Client side: Supports bidirectional latency measurement at the ODUk (k = 2(e), 3, 4, flex) layers.
• WDM side: Supports bidirectional latency measurement at the ODUC2/ODU4 PM and TCM layers.

Channel loopback

Supports ODUk(k=2(e),3,4,flex) channel inloops and outloops.

NOTE:

When the board is in service encryption mode, the loopback operation is not supported.

Port loopback

• Supports inloops and outloops on the WDM side.
• Supports inloops and outloops on the client side.

NOTE:

When the board is in service encryption mode, the loopback operation is not supported.

Alarm and performance event monitoring

• Supports the monitoring of section monitoring (SM)_bit interleaved parity 8 (BIP8) to help locate line failures.
• Supports the monitoring of path monitoring (PM)_BIP8 bytes to help locate faults.
• Supports the monitoring of B1 bytes to help locate faults.
• Supports the monitoring of OTN alarms and performance events.
• Supports the upstream and downstream RMON performance statistics of the 40GE/10GE/100GE service.
• Supports RMON performance statistics of Ethernet bandwidth utilization.
• Supports the monitoring of CD and PMD performance.
• Supports the monitoring of the bias current of the laser.
• Supports the monitoring of the temperature of the laser.
• Supports the monitoring of the optical power.