Huawei OptiXtrans E6600 Optical Transponder Unit TMB1LDX01 03033HCK

Basic function

Provides two tributary port and four line port to convert received client-side services into OTU signals.

Client-side service type

• STM-64: SDH services at a rate of 9.95 Gbit/s.
• OC-192: SONET services at a rate of 9.95 Gbit/s.
• OTU2: OTN service at a rate of 10.71 Gbit/s.
• OTU2e: OTN service at a rate of 11.1 Gbit/s.
• 10GE LAN: Ethernet services at a rate of 10.31 Gbit/s.
• 10GE WAN: Ethernet services at a rate of 9.95 Gbit/s.
• FC800: SAN service at a rate of 8.5 Gbit/s.
• FC1200: SAN service at a rate of 10.51 Gbit/s.
• FICON 8G: Fiber channel services at a rate of 8.5 Gbit/s.
• FICON 10G: SAN service at a rate of 10.51 Gbit/s.
• Infiniband 5G: SAN service at a rate of 5 Gbit/s.

NOTE:

• When Service Type is set to 10GE LAN and Port Mapping is set to Bit Transparent Mapping, the WDM-side port can be switched to the OTU2e mode only after cross-connections are created.
• When the FC1200 services (Bit Transparent Mapping) is received on the client side, the service is encapsulated into OTU2e signals and transmitted to the line side at a rate of 11.3 Gbit/s.

Service mapping mode

• 10GE service: Supports GFP-F or BMP mode.
• STM-64/OC-192/10GE WAN service: Supports asynchronous AMP or synchronous BMP mode.

NOTE:

The asynchronous AMP mode applies to interconnection with third-party NEs.

WDM specification

Supports the DWDM and CWDM specifications.

Tunable wavelength

Supports the optical tunable transponder. Equipped with this module, the board can tune the optical signal output on the WDM side within the range of 80 wavelengths in C-band with the channel spacing of 50 GHz.

FEC coding

WDM side: Supports FEC and AFEC-2 coding.

Line modulation format

Supports NRZ.

OTN overhead

• ODU2 layer: supports PM overhead processing.
• OTU2 layer: supports SM overhead processing.

LPT

Supports the LPT function when the client-side service is 10GE LAN.

Intra-board 1+1 protection

Supported

NOTE:

• When intra-board 1+1 protection is configured for the board, set "Cross-Connection Configuration Mode" to "Automatic".
• The board does not support extended intra-board 1+1 protection.

Client 1+1 protection

Supported

NOTE:

When FC services are received on the client side, inter-NE client 1+1 protection (the working and protection channels are not on the same NE) is not supported.

ODUk SNCP

Supported

NOTE:

When ODUk SNCP protection is configured for the board, set "Cross-Connection Configuration Mode" to "Manual".

L1 service encryption

Encrypts and decrypts OPUk payloads using the AES-256 CTR or GCM algorithm.

NOTE:

• The service encryption function of the board is authorized by the board license.
• Boards using different encryption algorithms cannot be interconnected.

Overtemperature protection

Supported. If the temperature of a board exceeds the upper threshold and services are affected, the board will automatically reset the key chips to prevent a board damage.

NOTE:

Only supported when the E6608T is used.

ALS

Supported on the client side when non-OTN services are received.

LLDP

Not supported

Physical clock

• When receiving 10GE LAN services on the client side:

Synchronous Ethernet transparent transmission is supported when the port service mapping path is bit transparent mapping (11.1G).

Synchronous Ethernet processing is supported when the port service mapping path is MAC transparent mapping (10.7G).

• WDM side: Physical Clocks is supported

IEEE 1588v2

• When 10GE LAN services are received on the client side and 10GE LAN MAC mapping (10.7G) is used, IEEE 1588v2 is supported.
• IEEE 1588v2 is supported on the WDM side.

ITU-T G.8275.1

• When 10GE LAN services are received on the client side and 10GE LAN MAC mapping (10.7G) is used, ITU-T G.8275.1 is supported.
• ITU-T G.8275.1 is supported on the WDM side.

ITU-T G.8273.2

Supported

High-precision clock synchronization

Supported

NOTE:

Only supported when the E6608T/ E6608/ E6616 is used.

Outband DCN

Supports ESC communication.

NOTE:

For details about the DCN types supported by the board, see "Feature Description - Outband DCN - Introduction to DCN - DCN Communication Channel - Comparison Between OSC and ESC".

Test frame

Supported, when 10GE LAN services received on the client side.

PRBS

10GE WAN/STM-64/OTU2/OTU2e/OC-192 services received on the client side: supports downstream PRBS.

Latency measurement

When non-OTN services are received, supports delay measurement at the ODU2 PM layer.

NOTE:

Delay measurement can be performed at only one port of an board at a time. In addition, ensure that two delay measurement tests are performed at an interval longer than 3 minutes.

Channel loopback

Not supported

Port loopback

• Supports inloops and outloops on the WDM side.
• Supports inloops and outloops on the client side.

Alarm and performance event monitoring

• Supports the monitoring of B1 bytes to help locate faults.
• Supports the monitoring of section monitoring (SM)_bit interleaved parity 8 (BIP8) to help locate line failures.
• Supports the monitoring of path monitoring (PM)_BIP8 bytes to help locate faults.
• Supports the remote monitoring (RMON) for 10GE LAN services.
• Supports the monitoring of the bias current of the laser.
• Supports the monitoring of the temperature of the laser.
• Supports the monitoring of the optical power.