TNS7N404,N404,03034EGG,Huawei OSN 9800 Universal Line Board

Huawei OSN 9800 100G Line Board TNS7N404 Overview

TNS7N404: 4 x 100Gbit/s Universal Line Service Processing Board

The N404 board consists of a OTN processing module, VC cross-connect module, SDH processing module, WDM-side optical module, control and communication module, and power supply module.

Functions and Features of the TNS7N404 Board (OTN Line)

Function and Feature	Description
Backplane capacity	The total backplane bandwidth is 400 Gbit/s.
WDM specification	Supports the DWDM specifications.
Tunable wavelength	Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
FEC coding	SDFEC2
Line modulation format	100G QPSK 100G QPSK wDCM
OTN overhead protocol	Supports the OTN frame format and overhead processing defined by ITU-T G.709.
OTN overhead	WDM-side OTU4 layer: supports SM overhead processing. ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports PM and TCM overhead processing. ODUk (k=0, 1, 2, 2e, 3, 4, flex) layer: supports non-intrusive monitoring of PM and TCM overheads.
Intra-board 1+1 protection	Supported NOTE: Supports intra-board 1+1 protection when working with optical protection boards.
ODUk SNCP	Supported
Tributary SNCP	Supported
Electrical-layer ASON	Supported
Optical-layer ASON	Supported NOTE: Only ASON without optical parameters is supported in high SOP mode.
Digital optical label	When LS Ability is enabled, the board supports loading low-frequency pilot-tone modulation signals and overheads during wavelength conversion, and can work the optical-layer board that supports the digital optical label function to detect optical power and overheads and report optical performance data.
Physical clock	Supported NOTE: When the ODU cross-connect granularity of an OTN line port is set to the maximum granularity supported by the port, physical clock synchronization is not supported. The physical clock can be used only after lower-order ODU cross-connections are configured.
IEEE 1588v2	Not supported
ITU-T G.8275.1	Not supported
ITU-T G.8273.2	Not supported
Outband DCN	Supports communication over ESCs.
Test frame	Not supported
PRBS	Supports the PRBS function on the WDM side.
Latency measurement	The board supports latency measurement in the WDM-side optical port direction (upstream direction).When higher-order ODU4 cross-connections are created on the board, TCM section latency measurement is supported for higher-order ODU4 channels. When lower-order ODUk cross-connections are created on the board, PM/TCM section latency measurement is supported for higher-order ODU4 channels, and TCM section latency measurement is supported for lower-order ODUk channels.
Channel loopback	ODUk (k=0, 1, 2, 2e, 3, flex) channel loopbacks
Port loopback	Supports WDM Side Loopback
Alarm and performance event monitoring	Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line failures. Monitors parameters such as the bias current, temperature, and optical power of the laser. Monitors OTN alarms and performance events.

Functions and Features of the TNS7N404 Board (SDH)

Function and Feature	Description
Basic function	Provides four line ports and supports conversions between SDH signals from the backplane and ODUk signals. For details about the service mapping path, see Application.
Backplane capacity	The total backplane bandwidth is 80 Gbit/s.
Service processing	VC-12, VC-3, VC-4, VC-4-4c, VC-4-16c, VC-4-64c
Overhead processing	Processes the section overheads of STM-16/STM-64 signals. Supports the transparent transmission and termination of path overheads. Supports the setting and query of the J0, J1, and C2 bytes. Supports ECC communication. Supports transparent transmission of DCC channels.
SDH SNCP	Supported
Linear MSP	Supported
Ring MSP	Supports two-fiber bidirectional ring MSP
SDH ASON	Supported
Physical clock	Supports SDH clock synchronization.
Outband DCN	Supported
Channel loopback	Supports VC loopbacks.
Port loopback	Supports Virtual Port loopbacks.
2M ASON	Supported NOTE: Only supported when the 9800 M24 is used.
Alarm and performance event monitoring	Provides various alarms and performance events, facilitating equipment management and maintenance.

Functions and Features of the TNS7N404 Board (Regeneration)

Function and Feature	Description
Basic function	Electrically regenerates optical signals at an electrical REG station.
Regeneration mode	Unidirectional regeneration Bidirectional regeneration
Regeneration rate	OTU4
WDM specification	Supports the DWDM specifications.
Tunable wavelength	Supports tunable wavelengths of WDM-side optical signals in Super C band (1524 nm to 1573 nm).
FEC coding	SDFEC2
Line modulation format	100G QPSK 100G QPSK wDCM
OTN overhead	WDM-side OTU4 layer: supports SM overhead processing. ODU4 layer: supports PM and TCM overhead processing. ODU4 layer: supports non-intrusive monitoring of PM and TCM overheads.
Electrical-layer ASON	Not supported
Optical-layer ASON	Supported NOTE: Only ASON without optical parameters is supported in high SOP mode. In unidirectional regeneration scenarios, for the WDM-side A51 or A62 optical module, the receive and transmit wavelengths must be the same. Both A51 and A62 modules do not support wavelength change by configuring regeneration boards.
ALS	Supported NOTE: When using the WDM-side A51 or A62 optical module, the board does not support the regeneration ALS function in unidirectional relay mode.
Outband DCN	Supports ESC communication.
Port loopback	In bidirectional regeneration mode, optical port outloop is supported. NOTE: Loopback of both ports is not supported.
Alarm and performance event monitoring	Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line failures. Monitors parameters such as the bias current, temperature, and optical power of the laser. Monitors OTN alarms and performance events.

Hunan Moka Information Technology Co., Ltd.

A professional import and export trade company specializing in the agency sales and services of the full range of Cisco products in the United States. Our product range includes Cisco switches, Cisco routers, Cisco firewalls, Cisco wireless APs, Cisco conference terminals, Cisco optical modules, Cisco fiber optic jumpers, Cisco industrial switches, and Cisco software licenses. As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects. As a result, you can obtain the best discounts from Cisco China, typically ranging from 60% to over 90%. Due to Cisco's global sales policy, if you order Cisco licenses, with your consent and permission, we will assist you in installing and activating Cisco licenses within China. Alternatively, you can activate them in your own country, and we will transfer the licenses to you. All you need is a Cisco Smart Account. When the Cisco licenses expire, you can choose to renew them yourself or contact us.

As an authorized distributor of Cisco in China, we directly purchase hardware and software from Cisco China in the name of projects.

Huawei OSN 9800 Universal Line Board TNS7N404 03034EGG

DETAILS

YOU MAY ALSO LIKE

Get a free consultation

Innovatively safeguards your investments for the future